API X52管线钢与Corus RQT 701超高强钢的焊接工艺

针对超高强钢在机械行业的广泛使用,焊接接头易出现淬硬脆化、裂纹等缺陷的情况,采用焊条电弧焊(SMAW)和药芯气体保护焊(FCAW-GS)组合的焊接方法,对API X52管线钢与Corus RQT 701超高强钢的焊接进行了工艺试验,并进行常规力学性能试验。结果表明,通过合理匹配焊接工艺参数,严格控制低热输入量及层间温度,实现了小熔合比的异种钢焊接,且焊接接头具有良好的力学性能,达到了标准和规格书的要求;异种高强钢焊接,采用SMAW打底焊接和FCAWGS填充并盖面的方法,焊接效率较单纯采用焊条电弧焊工艺提高2倍以上。     

细粒尾矿综合利用技术研究

姑山矿业公司为提高细粒尾矿的综合利用率，研究分析了细粒尾矿的性质，系统研究了尾矿含量、煅烧工艺制度对不同成分体系尾矿陶粒堆积密度、表观密度、空隙率、吸水率、筒压强度及软化系数的影响。研究得出了全尾矿陶粒、细粒尾矿+污泥陶粒、细粒尾矿+污泥+粉煤灰陶粒3种成分体系的尾矿陶粒较优的尾矿含量及煅烧工艺制度，且3种尾矿陶粒均可代替石头用作粗集料。     

Joining of dense Si3N4 ceramics with tape cast Lu-Al-Si-O-N interlayer

Lu-Al-Si-O-N tapes with different thickness were used to join gas pressure sintered Si₃N₄ ceramics. The microstructure of the joints and the influences of the joint thickness and joining temperature on the bonding strength of the as-joined Si₃N₄ ceramics have been investigated. The highest bonding strength about ~ 300 MPa of the joined specimens was achieved by using 450 µm interlayer at 1450 °C. The existence of Si₃N₄ nanowires was beneficial for the improvement of the bonding strength by interweaving the oxynitride glass matrix in the joint region.     

回弹检测法检测混凝土强度相关问题的探讨

本文就当前社会人们对建筑安全水平和质量要求不断提高的背景下,对回弹检测法检测混凝土强度的相关问题进行探讨,并以此推动回弹法检测混凝土强度行业标准的规范化发展进程,希望能够给从事相关行业的工作者提供帮助。     

P91钢管道异常低硬度部位的组织和性能

对电厂运行过程中发现的P91钢主蒸汽管道的低硬度部位进行了微观组织观察、短时力学性能试验和高温持久强度试验,分析了其硬度偏低的原因。结果表明,低硬度区域P91钢组织为铁素体+析出物,位错密度较低,M₂₃C₆相在晶界处粗化聚集,同时析出新相Laves相,使得P91钢的短时力学性能和高温持久强度下降严重。     

超高强7055铝合金铸锭均匀化工艺优化

采用光学显微镜、扫描电镜、差热分析及透射电镜等手段,对一种航空用超高强7055铝合金大尺寸铸锭的均匀化工艺进行分析与优化。提出分级提高均匀化温度的方法,在确保不发生过烧的情况下,最大限度改善铸锭质量。结果显示:低温预均匀化时,铸锭中析出大量的Al₃Zr相,能够大幅度降低对后续挤压变形的再结晶比例;对铸锭采用400 ℃×4 h+465 ℃×16 h+474 ℃×8 h的分级均匀化处理工艺,能够显著消除铸锭中低熔点相的含量,提高铸锭质量,同时相比于原工艺节省约13 h。新的均匀化处理工艺,不仅提高了生产效率,还能够为后续工艺提供良好的铸锭。     

Compressive strength and microstructure of alkali-activated fly ash/slag binders at high temperature

This paper reports the results of the compressive strength and microstructure of various alkali-activated binders at elevated temperatures of 300 and 600 °C. The binders were prepared by alkali-activated low calcium fly ash/ground granulated blast-furnace slag at ratios of 100/0, 50/50, 10/90 and 0/100 wt.%. Specimens free of loading were heated to a pre-fixed temperature by keeping the furnace temperature constant until the specimens reached a steady state. Then the specimen was loaded to failure while hot. XRD, SEM and FTIR techniques were used to investigate the microstructural changes after the thermal exposure. The fly ash-based specimen shows an increase in strength at 600 °C. On the other hand, the slag-based specimen gives the worst high-temperature performance particularly at a temperature of 300 °C as compared to ordinary Portland cement binder. This contrasting behaviour of binders is due to their different binder formulation which gives rise to various phase transformations at elevated temperatures. The effects of these transformations on the compressive strength are discussed on the basis of experimental results.     

Ergonomically based design of tractor control tools

Musculoskeletal injuries are well-known disorders among the agricultural tractor operators. Overexertion is a critical factor which can agitate these injuries. Physical body characteristics should be measured for an ergonomically best-fit-optimal design for the operators. In this study, a designed setup was employed to derive the applied forces by tractor operators on the control tools. The different muscle strengths including leg/foot strength, hand push/pull strength, and torque strength applied by both hands were measured. A comparison was made for the obtained values for different strengths by considering the effects of hand dominance. The obtained data were used to estimate the maximum allowed forces in these tools. In contrast to the previous studies, the minimum allowed actuating forces of the pedals were calculated using reasonable assumptions. These values could provide more comfort and less exhaustion for the tractor operators. The obtained ranges were benchmarked against corresponding recommended values in some standards (ISO, ISIRI, and ASABE family). The results revealed the unsuitability of evaluated standards for a proper design and the excessive overestimation of those recommended values (in some cases more than 3 times). In all of the design procedure, a suitable attention was paid to accommodate it with more than 90% of target population.Relevance to industryA prosperous industry which considers ergonomic factors in the design of agricultural machine workplace can overcome the disorders and generate more comfort. Evaluating more exact mechanical forces can result in a suitable design of workplace.     

碱度对熔剂性球团生球性能的影响

 熔剂性铁矿球团具有优良的高温冶金性能，是高炉炼铁的优质炉料。为探明生产熔剂性铁矿球团时碱度对生球性能的影响规律，以某钢厂赤铁精矿为原料，通过添加石灰石粉调节碱度，进行了造球及生球干燥特性试验研究。结果发现，提高碱度，生球落下强度呈提高趋势，抗压强度变化不明显，适宜膨润土配比略有下降，生球爆裂温度明显提高，生球干燥速率则没有明显变化。与基准自然碱度（R＝0.14）相比，当碱度提高到0.6以上时，适宜膨润土配比由1.2%下降到1.1%，生球爆裂温度提高近50 ℃以上。     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.